Maple Bat Rules And Main League Baseball
In response to Main League Baseball, 2,232 baseball bats had been broken by batters from July to the tip of the regular season. 756 of those bats broke into multiple pieces. An MLB research staff was brought in after several high profile accidents severely injured spectators, a base coach, 해외스포츠중계 and, finally, a plate umpire. Additionally, a number of close calls have been reported together with one with a workforce president and one with Bobby Cox, manager with the Atlanta Braves. The researchers discovered that maple bats have been three times as prone to shatter into multiple items than more traditional ash bats.
The researchers' suggestions were offered to MLB in December. While there are very doubtless numerous reasons for the dramatic ruptures fans witness with maple, researchers are at the moment specializing in the structure of wood grain for maple bats. Most notably, maple grains must be as straight as possible. Unlike ash, straight grains for maple are harder to find. Regardless of the type of wood, researchers feel bats are a lot more likely to fail when the so-called "slope of grain" is greater than one inch over a 20-inch length of the bat (just underneath three-degrees). In addition, the face of the bat that strikes the ball must be reconfigured by moving the trademark a quarter of a flip for maple.
To this finish, researchers have made a number of suggestions to MLB and these suggestions have essentially been transformed into regulations. A abstract of these regulations is given under:
Bats must adhere to a slope of grain requirement of just below 3-degrees for the handle and taper regions.
Bat makers should place an ink dot on the face grain side of the deal with for maple and birch bats to gauge the slope angle
The hitting surface for maple and birch needs to be the face grain, not the edge grain, that means 1 / 4 turn (ninety-degrees) placement of trademarks on bats
Handles for maple and birch bats must be both pure or clear finished (to see the grain and ink dot)
Bat makers need a system to track maple and birch bats that leave their shops
Bat makers need to take part in an MLB sponsored workshop on engineering and grading of wood
Bat makers shall be visited and audited for manufacturing processes and tracking systems
Audits will also be made randomly (does that sound familiar?) at ballparks
An on-going third-party certification program needs to be set up to cope with any new improvements that come along in the future
In addition, Main League Baseball has doubled its bat certification payment from $5,000 per company to $10,000. They've additionally doubled the liability insurance requirement from $5 million to $10 million.
In the long run, it's hoped that these measures will reduce the number of dangerous broken bat episodes for everybody enjoying America's pastime. However, these could also be just the primary steps that will likely be taken. Only time will tell.
The researchers' suggestions were offered to MLB in December. While there are very doubtless numerous reasons for the dramatic ruptures fans witness with maple, researchers are at the moment specializing in the structure of wood grain for maple bats. Most notably, maple grains must be as straight as possible. Unlike ash, straight grains for maple are harder to find. Regardless of the type of wood, researchers feel bats are a lot more likely to fail when the so-called "slope of grain" is greater than one inch over a 20-inch length of the bat (just underneath three-degrees). In addition, the face of the bat that strikes the ball must be reconfigured by moving the trademark a quarter of a flip for maple.
To this finish, researchers have made a number of suggestions to MLB and these suggestions have essentially been transformed into regulations. A abstract of these regulations is given under:
Bats must adhere to a slope of grain requirement of just below 3-degrees for the handle and taper regions.
Bat makers should place an ink dot on the face grain side of the deal with for maple and birch bats to gauge the slope angle
The hitting surface for maple and birch needs to be the face grain, not the edge grain, that means 1 / 4 turn (ninety-degrees) placement of trademarks on bats
Handles for maple and birch bats must be both pure or clear finished (to see the grain and ink dot)
Bat makers need a system to track maple and birch bats that leave their shops
Bat makers need to take part in an MLB sponsored workshop on engineering and grading of wood
Bat makers shall be visited and audited for manufacturing processes and tracking systems
Audits will also be made randomly (does that sound familiar?) at ballparks
An on-going third-party certification program needs to be set up to cope with any new improvements that come along in the future
In addition, Main League Baseball has doubled its bat certification payment from $5,000 per company to $10,000. They've additionally doubled the liability insurance requirement from $5 million to $10 million.
In the long run, it's hoped that these measures will reduce the number of dangerous broken bat episodes for everybody enjoying America's pastime. However, these could also be just the primary steps that will likely be taken. Only time will tell.
